- -zł1.00

Banner
C-STIX glue 200 ml - (DIMAFIX) ADHESIVE PREPARATION FOR 3D PRINTING
Polityka bezpieczeństwa (edytuj za pomocą modułu „Bezpieczeństwo klienta”)
Zasady dostawy (edytuj za pomocą modułu „Bezpieczeństwo klienta”)
Zasady zwrotu (edytuj za pomocą modułu „Bezpieczeństwo klienta”)
1 piece C-STICK 200 ml
Completely new C-Stick - in the form of an atomizer bottle
New C-Stick adhesive atomizer - a newly developed preparation for gluing prints to the table
3D printers. It comes in a 200ml spray bottle. Works great with platforms
glass (ceramic). It can also be used on other substrates.
• The preparation is completely washable from printouts and printer tables with warm water.
A small amount of soap / dishwashing liquid can be added for a faster effect.
• Increased adhesion strength for the most popular materials such as:
ABS, ASA, PCABS, PET, PETG, PLA.
• Easy to remove prints - after cooling the table, the prints very gently move away from the surface of the 3D printer table.
• Increased product efficiency in relation to pressure cans. One package is enough for up to 150 prints.
• No dusting when applying the preparation to the working table of the 3D printer.
• Etalon-based formulation instead of acetone - no acrid odor.
• Exponential increase in adhesion to build plate temperature. Higher temperature provides greater adhesion.
• Mirror finish of the bottom print layer.
• Can also be used on perforated tables (eg in Zortrax printers), steel or
aluminum.
Directions for use:
• Shake.
• Apply a thin layer of the preparation on a cool and degreased printer table (temperature below 50 ° C).
• Heat up the printer bed and start printing.
• After printing is finished, wait when the temperature of the platform is below 40 ° C and remove the printout.
Recommended temperatures for the most popular materials:
• PLA: 55-65 ° C
• PETG: 70-85 ° C
• ABS, ASA: 100-110 ° C
• PCABS: 110-120 ° C
The given temperature ranges are the values set in the program generating the G-Code. Due to the thermal conductivity of the materials it is made of
3D printer platform and the most common location of the temperature measurement sensor, the temperature on the build platform is usually lower than the set one. Due to the wide spectrum of available materials and their varieties,
design solutions of printer tables - their thermal conductivity and the quality of the measuring sensors themselves, these values are a reference point for the selection of appropriate
parameters for a given material and 3D printer.
Four zones of temperature-regulated adhesion strength:
• 20-40 ° C - printouts tear-off zone. Force
adhesion of prints is very small, so
printed details easily detach from the platform
without using much force or tools.
• 50-70 ° C - the first printing zone. The glue gains
adhesive properties allowing for printing details
from filaments with low shrinkage and geometry free
sharp transitions on the lower plane.
• 70-90 ° C - second printing zone,
characterized by high adhesion strength. Recommended for
medium and large prints of any geometry.
• 90-120 ° C - the third printing zone, where
the limit temperature of 120 ° C ensures the highest
with possible adhesion forces allowing very large printing
and intricate details, even with significant materials
contraction. Especially recommended for styrene materials
(including ABS) and related.
Reference: Regał - x
COROPad 202x255 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 225x255 MAGNETIC FLEX SYSTEM Podkładka Adhezyjna Druk 3D
Reference: Regał - x
Brand: COROTechnology
COROPad 255x255 MAGNETIC FLEX SYSTEM Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 202x202 Adhesive Pad. 3D Printing
Reference: Regał - x
COROPad 300x300 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 100x100 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 225x255 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 400x400 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 235x235 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 255x255 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 165x165 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 300x300 MAGNETIC FLEX SYSTEM Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 165x285 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 140x140 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 165x255 Adhesive Pad / Podkładka Adhezyjna Druk 3D
Reference: Regał - x
COROPad 165x255 Adhesive Pad / Podkładka Adhezyjna Druk 3D
C-STIX glue 200 ml - (DIMAFIX) ADHESIVE PREPARATION FOR 3D PRINTING